Corpus area - help/show me to replace the clutch

When are you planning on doing it and do you have tools etc.....

The Haynes/Chilton manual is your friend, Luke...use the force...

A decent transmission jack would be a plus also. The new clutch should come with an allignment tool. This question needs to be asked before you buy. Replace the pilot bushing/bearing (probably causing difficulty going into 1rst.) and the throw out bearing also.

If the flywheel shows signs of extreme heat (strange purple colors) take it off and have it resurfaced. Make some phone calls ahead of time, so you don't have to hunt the day of. Some flywheel bolts are 1 time use. They are lots cheaper than buying a crankshaft when the flywheel comes loose after you are done. Get the bolts from chrysler they are special. If you don't need to use them they will take em' back.

This would be a good time to change the oil in the tranny/transfer case also. If you drain them first they will be that much lighter.

I have not done a clutch in a TJ, but I have done many from Cranes, Heavy trucks, all the way down to a subaru. I hope this helps with out preachin', good luck, take your time, keep track of all of the bolts, and let me know if you get bound up. Randy

Oh yeah, There is a great parts house in Ingleside...smart guys, lots of help. They would probably be able to handle that flywheel...or know where to go, fyi.

I can't remember the name, they are on the road to the Naval base, and Gulf Marine if that helps. The Gulf Coast Pirate should know...he works pretty close to it.

Hey Raul, I would be glad to help when you're ready. I've done a few clutches on 4WD vehicles so I know it is a lot easier with at least 2 people. Just let me know at least a week ahead of time so I can make plans.

potlickinpirate wrote:

Oh yeah, There is a great parts house in Ingleside...smart guys, lots of help. They would probably be able to handle that flywheel...or know where to go, fyi.

I can't remember the name, they are on the road to the Naval base, and Gulf Marine if that helps. The Gulf Coast Pirate should know...he works pretty close to it.

You must be thinking about Bills Auto Supply...they are great guys, I have done quite a bit of business with them, as a matter of fact I used to live right next door to it!!

I've never done a clutch repair or anything like that, but I would like too learn for experience and what not. Plus actually meet some of yall dudes.
Let me know and id be in to help with what i can.

Tvernon wrote:

I've never done a clutch repair or anything like that, but I would like too learn for experience and what not. Plus actually meet some of yall dudes.
Let me know and id be in to help with what i can.

Cool. I will let you know when we will meet. I am aiming for the last weekend of April. I still need to buy the clutch. I am leaning towards a LUK.

I am also planning on replacing the timing chain, lifters and camshaft to the Wrangler in the following months so I am sure there will be opportunities to meet! (if people want to help me replace them)

If I get the heep up and running by the end of April I will be glad to and give you a hand, I've never changed a clutch either, but I'm sure we can figure it out.

I mean how hard can it be?

Luke=Good

then its on!!!!!

I mean how hard can it be?[/quote]



I just finished one on a 35 ton crane, no transfer case but with a pto and a large hyd pump. The trans weighs 1000#. I can tell you some stories...

I'm in. I have some tools. jack stands, blah blah blah. Need a line up pin, and a good tranny jack would be nice (you can rent those). Just give me a call, and we'll get it done! 903 424 5714

-Kenny

May 1 should be ok for me. It may have to be in the evening, as I have to supervise a pipeline shutdown that morning.

id be in on that i have finals im thinking at the end of that week but most will be papers so im still in man May first is good, just let me know were im going.

id be in on that i have finals im thinking at the end of that week but most will be papers so im still in man May first is good, just let me know were im going.

As far as I know that day should work for me..

Sat the first? isnt that the K2 memorial day run?

r_unda wrote:

GULF COAST PIRATE wrote:

Sat the first? isnt that the K2 memorial day run?

I think that’s on May 29-31 but I might be wrong. I am debating if I should go to that.

toddandshari'sjk wrote:

As far as I know that day should work for me..

Great! Clutch should be here this Friday. I will PM you guys my address sometime closer to the date.

You should go! Twylla and I are going.