Gulf Coast Chapter Monthly Meeting September

Colin, give me a call. I've got some flat bar left over from the light bar project.

-Kenny

Ok, Who has Aug?

this was sent to me on Thursday Aug 5th... FYI


just a reminder we're having a meeting tomorrow at 7pm at Wings N' Beyond at 15013 Northwest Blvd. (FM 624) it's right across from Wood River and between a tire shop (Northwest Tire if I remember correctly) and the Garage Bar and Grill. as your heading west on 624 it will be on the left hand side and is best to turn in the driveway of the tire shop and into the parking lot of Wings N Beyond. hope to see ya'll there


Scott

Dammit! thats right. I missed it and forgot. Damn ADD.

GULF COAST PIRATE wrote:

Ok, Who has Aug?

You mean Sept? I think its Tyler turn

Raul, Dont mind the jack stands and other materials necessary for the aussie install, but I dont have a place or the funds for a floor jack, im guessing the stock jack and scrap wood will work?

CCGRUNT0331 wrote:

Raul, Dont mind the jack stands and other materials necessary for the aussie install, but I dont have a place or the funds for a floor jack, im guessing the stock jack and scrap wood will work?

My Hi-lift jack should work just fine, I use it all the time. If not I have a small car floor jack that we can probably use.

going to tackle the aussie on thursday or friday, wish me luck! and pm me if ya wanna watch or even help!

CCGRUNT0331 wrote:

Raul, Dont mind the jack stands and other materials necessary for the aussie install, but I dont have a place or the funds for a floor jack, im guessing the stock jack and scrap wood will work?

I have a floor Jack you can borrow if you do it during the week as I will need it saturday!

God Bless my brother... the little shit is kicking me out of his garage where I planned on doin the install all because I told him to grow up and call into work... ahh, should happen this weekend now...

if you wanna come over to my place i have just about everything you could possibly need to do the install and i'm off this week and next week

my garage is open too. Sorry for my absence recently. I've been moving into the new place. I've got a big bottle jack, and a pair of stands availible as well.

Thanks guys! I am planning on leaving work early on friday and just knocking it out. shawn I think I have your number and kenny I know I got yours, so Ill give yall a call on friday if I need a place or not... I really appreciate the offer guys thats sayin a lot for the Jeep Community

Updated the origional Post.

September 18th Ill be in Wimberly for a wedding, count me out, sorry guys!

Count me in, I should be able to make it either day. Whatever works the best for everyone but I prefer Saturday. Let me know in what I can help.

i might be able to make it this time

17th works for me but I will make it to either day!

If we decided to do this on the 18th, can we make this meeting and install party also? I need to replace my "new" clutch throwout bearing.

I hope to be able to make it. something sticks in my mind that weekend but I'm not sure what it is...

yeah the 18th is good for me too, sorry ive been out for a bit. school started up for me again so my life went right down the drain.

Is the meeting going to be on the 17th or the 18th?

CCGRUNT0331 - won’t be able to attend
shawn - maybe
roadkill - maybe
Constantine - able to make it either day
Tvernon - 18th works for him
r_unda - able to make it either day

What about the guys on the email list? What day do they prefer? Kenny what day do you prefer since its going to be at your place?

I wanted to replace my clutch TO bearing during the meeting but I am getting lazy, I think I would just rather relax and enjoy the meeting.

If I can barrow some of you guys jack stands and jacks I would appreciated it that way I can just slowly do it after work next week.

Raul

r_unda wrote:

Is the meeting going to be on the 17th or the 18th?

CCGRUNT0331 - won�t be able to attend
shawn - maybe
roadkill - maybe
Constantine - able to make it either day
Tvernon - 18th works for him
r_unda - able to make it either day

What about the guys on the email list? What day do they prefer? Kenny what day do you prefer since its going to be at your place?

I wanted to replace my clutch TO bearing during the meeting but I am getting lazy, I think I would just rather relax and enjoy the meeting.

If I can barrow some of you guys jack stands and jacks I would appreciated it that way I can just slowly do it after work next week.

Raul

I like the 18th in the afternoon.
No word on the other guys on the email list. guess they'll give me a shout if they can come.

Bring drinks and anything you care to contribute. I'll have some adult beverages as well as sodas. I've got the Shrimp and Crab and Possibly some Crawfish. If there's something else you want or you dont eat seafood, Let me know, there may be some grilling going on as well. If anyone has one of those big fans, and wants to loan it, I'll gladly come get it this week so we'll have it this weekend.

As usual, you guys and gals from Houston and San Antone are welcome to make the drive to Portland.

Raul, If you want to show up early we'll get that bearing knocked out. If not, I have two jack stands and a 12k bottle jack at your disposal.

I might be in your neck of the woods later this week, either Wednesday/Thursday or Thursday/Friday. I won't be able to go to the install party, but should be good for a couple of beers in the evening.

Dutchboy101 wrote:

I might be in your neck of the woods later this week, either Wednesday/Thursday or Thursday/Friday. I won't be able to go to the install party, but should be good for a couple of beers in the evening.

JUST LET ME KNOW!